• JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
 
  Bookmark and Share
 
 
Master's Dissertation
DOI
https://doi.org/10.11606/D.18.2017.tde-30112017-165852
Document
Author
Full name
Michael Miguel Furlanetti
E-mail
Institute/School/College
Knowledge Area
Date of Defense
Published
São Carlos, 2014
Supervisor
Committee
Montanari, Luciana (President)
Button, Sergio Tonini
Evangelista, Sérgio Henrique
Title in Portuguese
Estudo do comportamento das deformações em flanges obtidos pelo processo de estampagem incremental através de elementos finitos e projeto de um suporte modular
Keywords in Portuguese
Elementos finitos
Estampagem incremental
Flanges
Mecânica da deformação
Suporte modular
Abstract in Portuguese
A estampagem incremental é um processo de deformação incremental de chapa que pode ser classificado em três modos distintos: estampagem incremental sem matriz, estampagem incremental com matriz parcial e estampagem com matriz total. A deformação ocorre devido ao contato entre a ferramenta e a chapa, localmente e progressivamente, ao longo de uma trajetória pré-definida. A chapa permanece presa a suportes que fixam as suas extremidades de maneira a impedir os deslocamentos provocados pela passagem da ferramenta. A primeira parte deste trabalho compreende estudos em elementos finitos, usando o software LS-Dyna, sobre a trajetória das deformações na estampagem incremental para a fabricação de flanges em chapas previamente furadas de liga de alumínio AA1050. Foram realizados testes de contato e de linha que permitiram definir parâmetros da simulação. Os resultados para as deformações foram confrontados com os resultados obtidos experimentalmente por outros autores e permitiram verificar o comportamento das deformações nos flanges. As deformações crescem montonicamente até os valores máximos. Este resultado confirma a teoria de que na estampagem incremental de chapas a fratura ocorre sem o prévio aparecimento da estricção. A segunda parte deste trabalho trata do desenvolvimento de um suporte modular aplicável a estampagem incremental, tanto na sua variante sem matriz quanto com matriz, com o intuito de aumentar a flexibilidade do processo com relação à geometria da peça a ser deformada. Foi empregada a técnica de análise de valor objetivando alcançar a melhor funcionalidade do sistema. Como resultado foi obtido um suporte modular que atende os requisitos de rigidez, flexibilidade, modularidade, agilidade na troca da chapa a ser deformada e simplicidade construtiva.
Title in English
Study of the behavior of deformations in hole-flanging produced by incremental sheet forming using finite elements and design of a modular rig
Keywords in English
Deformation mechanics
Finite elements
Hole-flanging
Incremental sheet forming
Modular rig
Abstract in English
The sheet incremental forming can be classified into three basic configurations, depending on the number of contact points between the sheet, tool and die (when present). Single incremental forming (absence of specific dies) and two point incremental forming (presence of a partial or full die) can be distinguished. The process makes use of a simple, low-cost, hemispherical tipped tool to precisely and progressively shape a blank into a metal sheet along a predefined tool path. The sheet is fixed onto the rig to prevent lateral displacements caused by tool movement. The first part of this work includes studies about finite elements, using the LS-Dyna software, applied to deformation path in hole-flanging produced by incremental sheet forming. The investigation was carried out using aluminum alloy AA1050. Contact and line numerical results support simulation parameters choices. The results from the strains were compared with empirical ones obtained by other authors. The results showed the deformation mechanics behavior of the hole-flanging. The strain paths of hole-flanging produced by incremental sheet forming grew linearly and monotonically from the origin to the maximum achievable strains. This result confirms the absence of local necking along plane strain directions. The second part of this work deals with the development of a modular rig that can be applied to dieless, partial or total die single point incremental forming in order to increase the flexibility of the process concerning the geometry of the part to be deformed. The result was a modular rig with constructive simplicity and requirements of stiffness, flexibility and modularity when exchanging sheets.
 
WARNING - Viewing this document is conditioned on your acceptance of the following terms of use:
This document is only for private use for research and teaching activities. Reproduction for commercial use is forbidden. This rights cover the whole data about this document as well as its contents. Any uses or copies of this document in whole or in part must include the author's name.
Publishing Date
2017-12-01
 
WARNING: Learn what derived works are clicking here.
All rights of the thesis/dissertation are from the authors
CeTI-SC/STI
Digital Library of Theses and Dissertations of USP. Copyright © 2001-2024. All rights reserved.