• JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
 
  Bookmark and Share
 
 
Mémoire de Maîtrise
DOI
https://doi.org/10.11606/D.25.2003.tde-27112004-111927
Document
Auteur
Nom complet
Anuradha Prakki
Unité de l'USP
Domain de Connaissance
Date de Soutenance
Editeur
Bauru, 2003
Directeur
Jury
Mondelli, Rafael Francisco Lia (Président)
Carvalho, Ricardo Marins de
Villela, Lauro Cardoso
Titre en portugais
Resistência ao desgate de cimentos resinosos submetidos à ciclagem de pH e escovação simulada
Mots-clés en portugais
cimentos de resina
cimentos dentários
escovacao dentaria (simulacao)
Resumé en portugais
A importância da avaliação da resistência ao desgaste de cimentos resinosos se justifica, uma vez que estes podem ser expostos ao meio bucal em função do grau de desadaptação das restaurações estéticas indiretas, tornando-os susceptíveis às degradações físicas, químicas e mecânicas. Neste contexto, o objetivo deste trabalho foi avaliar a resistência ao desgaste, por meio da escovação simulada, de três cimentos resinosos, Enforce (Dentsply), Rely X (3M) e Variolink II (Vivadent) quando comparados a dois materiais de restauração indireta, Artglass (Heraeus Kulzer) e Duceram Plus (Ducera), através da alteração de massa e rugosidade superficial. Foram confeccionados 100 corpos de prova, 20 para cada material testado, onde metade foi submetida aos ciclos dinâmicos de pH previamente à escovação simulada. Os espécimes foram submetidos a 100.000 ciclos de escovação, utilizando-se escovas dentais macias (Oral B) e pasta dental (Colgate) diluída em água deionizada. A alteração de massa foi verificada pela diferença entre massa inicial (antes da escovação) e final (após escovação) em balança analítica. A alteração da rugosidade superficial (Ra) foi determinada pela diferença entre a média de cinco leituras iniciais (antes da escovação) e cinco leituras finais (após escovação) com rugosímetro Hommel Tester T 1000. Os resultados foram submetidos à análise de variância e teste de Tukey (p<0,05). A porcelana Duceram Plus não foi influenciada pela ciclagem de pH e, apresentou o melhor comportamento frente ao teste de escovação simulada. Entre os materiais resinosos, o Artglass e o Variolink II apresentaram os melhorescomportamentos para alteração de massa e rugosidade superficial, seguidos do Rely X e Enforce. A ciclagem de pH não influenciou estatisticamente no desgaste dos materiais avaliados.
Titre en anglais
Resin cements wear resistance evaluation under brushing abrasion preceded by pH cycling simulations
Mots-clés en anglais
dental cements
resis cements
toothbrushing (simulation)
Resumé en anglais
Indirect aesthetic restorations have been found to have a wide variation on its adaptation, subjecting consequently, the luting material to the oral environment degradation provided by physical, mechanical or chemical processes. Thus, theirwear resistances still worry researchers. In this context, the objective of this work was to evaluate the wear resistance of three resin luting cements, Enforce (Dentsply),Rely X (3M) and Variolink II (Vivadent) when compared to the following indirect restorative materials, Artglass (Heraeus Kulzer) and Duceram Plus (Ducera). All the material was subjected to dynamic pH cycles and to brushing simulation and the wear was detected by their weight and surface roughness changes. A hundred specimens were obtained, twenty for each material, half of them (ten for each material) was submitted to dynamic pH cycles before the brushing strokes. For the abrasion test, the specimens were subjected to 100.000 cycles of brushing with soft bristles tips (Oral B) containing dentifrice solution (Colgate) and deionized water. The weight loss was detected by the difference between the initial (before brushing strokes) and final measurements (after brushing strokes). The evaluation of surface roughness was obtained by the difference between initial and final means after five roughness readings in a Hommel Tester T 1000 testing machine. The results (ANOVA and Tukey) showed significant differences of weight loss and surface roughness among the tested materials.Duceram Plus was not influenced by pH cycling and presented the best performance after tooth brushing test. Among composite materials, Artglass and Variolink II presented better results for weight and roughness alterations followed by Rely X and Enforce. PH cycling did not influence statistically on tested materials wear resistance.
 
AVERTISSEMENT - Regarde ce document est soumise à votre acceptation des conditions d'utilisation suivantes:
Ce document est uniquement à des fins privées pour la recherche et l'enseignement. Reproduction à des fins commerciales est interdite. Cette droits couvrent l'ensemble des données sur ce document ainsi que son contenu. Toute utilisation ou de copie de ce document, en totalité ou en partie, doit inclure le nom de l'auteur.
AnuradhaPrakki.pdf (5.88 Mbytes)
Date de Publication
2004-12-09
 
AVERTISSEMENT: Apprenez ce que sont des œvres dérivées cliquant ici.
Tous droits de la thèse/dissertation appartiennent aux auteurs
CeTI-SC/STI
Bibliothèque Numérique de Thèses et Mémoires de l'USP. Copyright © 2001-2024. Tous droits réservés.